- provides easier information of the currently active domain
- tested by patching a running node

Set the MAC-adress for the WAN interfacce in case it is defined in the
board-data.

This commit fixes random MAC-Addresses on reboot in case OpenWrt stores
them in the device network configuration.

Fixes #2808

Signed-off-by: David Bauer <mail@david-bauer.net>

Currently the 'channels' setting of a 5G radio gets overwritten or
deleted even if the 'preserve_channels' option is enabled. Don't touch it
if 'preserve_channels' is set.

add comments about lacking radios
Co-authored-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Co-authored-by: Matthias Schiffer <mschiffer@universe-factory.net>

The activated setup mode is indicated by the WLAN LED.

Co-authored-by: David Bauer <mail@david-bauer.net>

update lan, wan separation for o2 6431

This reverts commit 543eb178.

Restores the dns caching configuration that should be feasible, since we
now require around 8 MB of flash.

Signed-off-by: Stefan Weil <sw@weilnetz.de>

Add cellular configuration support to Gluon. This implementtaion focuses
not on hotpluggable WWAN adapters but instead on embedded LTE modems
found in travel-routers or FWA CPEs.

Signed-off-by: David Bauer <mail@david-bauer.net>

as well as the target itself

If the uci option 'gluon.wireless.preserve_channels' is set then the channel width of wireless radios (htmode) is preserved during updates, too.

Use the country3 option implemented in OpenWrt's hostapd configuration
handling instead of adding it as a custom option.

Signed-off-by: David Bauer <mail@david-bauer.net>

Signed-off-by: David Bauer <mail@david-bauer.net>

This method previously returned the string literal of the config key,
leading to checks evaluating to true even in case this option was
disabled.

Signed-off-by: David Bauer <mail@david-bauer.net>

The preserve_channels configuration option was moved to the gluon UCI
package without adding a proper migration.

Signed-off-by: David Bauer <mail@david-bauer.net>

Gone due to
commit 45c84a11 ("ar71xx: drop target")

Depending on the source of the primary MAC address, uppercase digits
would be used on some devices. Convert the address to lowercase for
consistency.

We only change the case for newly configured nodes to avoid changing the
node ID and derives MAC addresses for existing installations.

Only restore the netifd proto for the WAN bridge in case the upgrade is
done from an older Gluon version.

For DSL targets, OpenWrt defaults the WAN proto to pppoe, while Gluon
uses the Ethernet ports for WAN. When unconditionally preserving the WAN
proto, pppoe is carried over to Gluon's network config.

Signed-off-by: David Bauer <mail@david-bauer.net>

Co-Authored-By: J. Burfeind <github@aiyionpri.me>

Co-authored-by: Tim-Niklas Koch <info@tnkoch.de>
Co-authored-by: J. Burfeind <github@aiyionpri.me>

There was never a device with a dedicated WAN port supported in Gluon
which could make use of such a workaround.

As the only relevant lantiq-xrx200 target now uses swconfig anyways,
we can remove this workaround.

Signed-off-by: David Bauer <mail@david-bauer.net>

Gone due to
commit 45c84a11 ("ar71xx: drop target")

Co-authored-by: Maximilian Baumgartner <aufhaxer@googlemail.com>

Gone due to
commit 45c84a11 ("ar71xx: drop target")

Gone due to
commit 071cf7b2 ("Switch to Lua for target definitions")

Has prior been introduced as untested -> broken in
commit d586720c ("ar71xx-generic: add support for Ubiquiti NanoBeam M5")

Was commented out in the former commit.

The new "value" helper can be used to turn a Lua value into a path that
can be passed to need_*() etc.

Removed in 45c84a11 ("ar71xx: drop target").

Gone due to
commit 45c84a11 ("ar71xx: drop target")

Instead of using roles.wan directly as the default for roles.single,
create a copy of the table, so subsequent modifications of roles.single
don't affect roles.wan as well.

Fixes migration of Mesh-on-WAN status when no default for "single"
interfaces is set in site.conf.

The function failed when an interface has no roles assigned, breaking
several upgrade scripts.

Closes #2471

Make the code match the docs and check_site.lua by actually looking up
the "default_roles" field, not "roles".