Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) QCA9563 integrated (3x3)
  - 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board

As upstream now has model detection for the Ubiquiti UniFi AC LR, we
need to provide an autoupdater image matching the expected filename.

Closes #1834

It seems the CT variant was used for 11s meshing on x86 by accient. Switch
to non-CT to match the other targets.

This commit removes the broken flag for the ipq806x-generic target,
as the first device (NETGEAR R7800) now has full support in Gluon

This commit accounts for the target renaming which was done in upstream
commit 7407e723991 ("ipqx0xx: add Generic subtarget")

This commit accounts for the target renaming which was done in upstream
commit 7407e723991 ("ipqx0xx: add Generic subtarget")

Their kernel partition is too small, the OpenWrt build system
is unable to create an image.

This changes the ath10k firmware and driver selection, as
ath10k-ct is now the default in upstream OpenWrt.

However, for 802.11s operation we need the QCA firmware and driver.

This is necessary, as wpad-basic conflicts with hostapd-mini.

This adds previously absent ath10k packages definitions. This way,
devices correctly select CandelaTech firmware correctly, when
GLUON_WLAN_MESH is set to IBSS.

This is also necessary for all devices, when OpenWrt is switched to
19.07.

fixes #1834
fixes #1332

The OCEDO Koala was missing the correct package definition. Because of
this, firmware is potentially built with the wrong ath10k firmware /
driver.

The kernel partition on these devices is too small for the
OpenWrt 19.07 kernel. It is also located after the rootfs, so
we cannot grow it further.

Therefore mark these devices as deprecated now.

reduce size by removing dispensable packages,
to fix builds of this target in most cases.

This reverts commit fb08e104.

Devices featuring ath10k radios should at least 128 MB of memory
as their driver is quite memory hungry.

Devices with a configuration (1x ath10k, 64M memory) like this have
often been seen as running out of memory.

The profile for GL.iNet AR750 currently selects ATH10K_PACKAGES, but this device actually has a QCA9887 which needs another driver.
This commit fixes the issue by setting ATH10K_PACKAGES_QCA9887 instead.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

memory usage seems to behave more reasonable for a while now

The old bash-based parsing code was way too complex. Replace it with Lua.

This device doesn't have an Ethernet port, and even with the Ethernet
shield, eth0 is not configured.

For some reason, some of the target files were executable.

Signed-off-by: Petr Štetiar <ynezz@true.cz>

Signed-off-by: Jan-Tarek Butt <tarek@ring0.de>

By passing the package name through merge_packages, it becomes possible to
override the package choice in GLUON_SITE_PACKAGES again, for example:

	GLUON_SITE_PACKAGES += -hostapd-mini hostapd