TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G  : *:0F

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

VoCores aren't exactly useful mesh nodes except for experimentation.
They certainly aren't worth maintaining a whole target, in particular
one that has a WLAN driver not used by any other target.

Signed-off-by: David Bauer <mail@david-bauer.net>

Specifications:

- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
                      - Non-programmable (shows WAN activity)
- Button: Reset

How to install:

1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
   Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
   the router..
5- It takes around 2 minutes. After that router will restart itself
   to OpenWrt.

Specifications:

- SoC:      MediaTek MT7621
- Flash:    16 MiB NOR SPI
- RAM:      128 MiB DDR3
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0:    MT7603E 2.4GHz 802.11b/g/n
- WIFI1:    MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable "power" LED (two-coloured, yellow/blue)
            Non-programmable "internet" LED (shows WAN activity)
- Buttons:  Reset

Installation:

Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on".

Vendor firmware won't accept any serial input until "uart_en" is
set to "1".

Using the https://github.com/acecilia/OpenWRTInvasion exploit you
can gain access to shell to enable these options:

To enable uart keyboard actions - 'nvram set uart_en=1'
To make uboot delay boot work - 'nvram set boot_wait=on'
Set boot delay to 5 - 'nvram set bootdelay=5'

Then run 'nvram commit' to make the changes permanent.

Once in the shell (following the OpenWRTInvasion instructions) you
can then run the following to flash OpenWrt and then reboot:

'cd /tmp; curl https://downloads.openwrt.org/...-sysupgrade.bin
  --output firmware.bin; mtd -e OS1 -r write firmware.bin OS1'

Fixes commit 89dc6b20 ("ramips-rt305x: drop devices with insufficient flash")

Signed-off-by: David Bauer <mail@david-bauer.net>

This device is a dual 5GHz device. It is recommended to manually change the
radio of the first device to the lower 5GHz channels and the second radio
to the upper 5GHz channels

* ar71xx-generic: only create manifest alias for Rocket M5

This follow up the discussion done in #2070 by not  creating a symlink
for the Rocket M5. Images for the Rocket M2 can still be flashed on a
Rocket M5.

This change will prevent the Rocket M5 from appearing in Firmware
selectors. Existing devices will still receive updates, as the device
name is still referenced for the device name expected by the M5.

Closes #2070

* docs: remove Rocket M5 from supported devices

Fixes #2113

Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>

This device has broken Ethernet on both ports.

Remove support for those devices. for now, as there was no feedback from
the original author.

Closes #1943

v2 is available on the market, but apparently has no upstream support, yet:
https://forum.openwrt.org/t/v2-of-cudy-wr1000/56965

- vendor name should not be part of model name
- there's no other version, hence mentioning the version is superfluous