defaults to 11s, allowing to build devices without IBSS-support

obsoletes GLUON_ATH10K_MESH

BROKEN because of stability issues with 5GHz enabled.

Fixes #1021

These devices have never actually existed; the corresponding support
strings have been removed from the stock firmwares as well.

The Airgateway LR is the same device as the normal Airgateway but with an detachable antenna. The Pro version is a cheap dual band device.

Fixes #1084

Hardware is very similar to Archer C5v1 and C7v2.

Tested factory install and autoupdater.

IBSS Mesh on 2.4 and 5 GHz is working fine.

The only Ethernet Port is used for config mode and afterwards handled
as WAN Port.

The size of the factory images is limited to 4MB, which caused build
failures when many additional packages were included.

Rather than moving the device to ar71xx-tiny, we ignore the factory images
and just build the sysupgrade. This way, the whole flash is usable for
Gluon.

This means that installing Gluon on these devices will now require to flash
a plain LEDE image first, and then upgrading using the Gluon sysupgrade
image.

Fixes #1020

These devices don't have unique MAC addresses with OpenWrt/LEDE at the moment
(see #993).

Closes #844

Fixes #961

Tested-by: Jannis Pinter <jannis@pinterjann.is>

The GLUON_ATH10K_MESH must be set to 11s or ibss; when it is not set,
ath10k device images won't be built at all. This also allows us to remove
the BROKEN flag for ath10k devices, as the GLUON_ATH10K_MESH variable is
sufficient to avoid ath10k devices if desired.

Fixes #864

The MR1750 and OM5P-AC devices are based on ath9k SoCs and an external
ath10k chip. All devices which are using ath10k should be marked as broken
due to deficits in their IBSS support.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

+ added profile for these devices
+ added entry in the docs for these devices plus the missing alfa tube

Generate flashable images for the Archer C7 v2 with current stock firmware
again.

To set the region code, the GLUON_REGION variable must be set to "us" or
"eu" in site.mk or as a make argument.

Fixes #860

Fixes #800

This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images.

The problematic patch switching the CPE510 to the secondary ART is left
out.

I've bought a couple of those devices from Senetic GmbH.

https://www.senetic.de/product/TL-WR842N



They have 16 MB of Flash and 64 MB of RAM. Platform support works fine,
I've also tested a little with Ethernet (since I saw some regressions on
OpenWRT/LEDE with 841v11), no problems.

Therefore, lets remove the broken mark.

Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>

Add Buffalo WZR-HP-G300NH2 to Makefile, device is already supported in OpenWrt and LEDE.
Verified functionality with actual device.

Fixes autoupdater for Hotnet-UB and AP121. Also add note about broken
autoupdates on Tube2H.

Also switch to kmod-ath10k-ct, so we can drop our AP+IBSS patch.

The new MR1750v2 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

The new OM2P-HSv3 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

This reverts commit ffd1f0b3.

Mainly applying a vendor patch from https://github.com/domino-team/OpenWrt-patches

(https://raw.githubusercontent.com/domino-team/OpenWrt-patches/master/AR150%2C%20AR300%2C%20Domino%20-%20CC1505/000-gl-ar150-cc.patch)

This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images, so the
CPE510 can use the correct ART offset, improving the TX power by 10dB.

Fixes #796