Tested-by: Jannis Pinter <jannis@pinterjann.is>

The GLUON_ATH10K_MESH must be set to 11s or ibss; when it is not set,
ath10k device images won't be built at all. This also allows us to remove
the BROKEN flag for ath10k devices, as the GLUON_ATH10K_MESH variable is
sufficient to avoid ath10k devices if desired.

Fixes #864

The MR1750 and OM5P-AC devices are based on ath9k SoCs and an external
ath10k chip. All devices which are using ath10k should be marked as broken
due to deficits in their IBSS support.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

+ added profile for these devices
+ added entry in the docs for these devices plus the missing alfa tube

Generate flashable images for the Archer C7 v2 with current stock firmware
again.

To set the region code, the GLUON_REGION variable must be set to "us" or
"eu" in site.mk or as a make argument.

Fixes #860

Fixes #800

This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images.

The problematic patch switching the CPE510 to the secondary ART is left
out.

I've bought a couple of those devices from Senetic GmbH.

https://www.senetic.de/product/TL-WR842N



They have 16 MB of Flash and 64 MB of RAM. Platform support works fine,
I've also tested a little with Ethernet (since I saw some regressions on
OpenWRT/LEDE with 841v11), no problems.

Therefore, lets remove the broken mark.

Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>

Add Buffalo WZR-HP-G300NH2 to Makefile, device is already supported in OpenWrt and LEDE.
Verified functionality with actual device.

Fixes autoupdater for Hotnet-UB and AP121. Also add note about broken
autoupdates on Tube2H.

Also switch to kmod-ath10k-ct, so we can drop our AP+IBSS patch.

Needs more testing, high packet loss at the moment.

build-tested with 2016.1.4, boots but packet loss on eth0
omitted ata due to build errors

Fixes #121

Based-on-patch-by: Tobias Hachmer <tobias@hachmer.de>

The new MR1750v2 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

The new OM2P-HSv3 device support is only available in LEDE master. The
relevant patches have to backported to add support for them in Gluon

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

This reverts commit ffd1f0b3.

Mainly applying a vendor patch from https://github.com/domino-team/OpenWrt-patches

(https://raw.githubusercontent.com/domino-team/OpenWrt-patches/master/AR150%2C%20AR300%2C%20Domino%20-%20CC1505/000-gl-ar150-cc.patch)

This patchset enables the RX LNA for the CPE210/510, improving RX by about
20dB. The profiles for CPE210 and CPE510 is split into two images, so the
CPE510 can use the correct ART offset, improving the TX power by 10dB.

Fixes #796

No sysupgrade support yet.

The returned name for OpenMesh devices with a an extra vX when calling

    lua -e 'print(require("platform_info").get_image_name())'

doesn't contain a dash between the vX and the device name. Thus the image
should also not contain a dash.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

The new ath9k/ath10k based devices are only available in OpenWrt trunk. The
relevant patches have to backported to add support for them in Gluon

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

The workaround to generate sysupgrade images for OpenMesh devices in gluon
is replaced in LEDE/OpenWrt by a special patch. It is therefore better to
drop the workaround and use the upstream version.

Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Integrate OpenMesh devices available in OpenWrt Chaos Calmer:

 - MR600
 - MR600v2
 - MR900
 - MR900v2
 - OM2P
 - OM2P-HS
 - OM2P-HSv2
 - OM2P-LC
 - OM2Pv2
 - OM5P
 - OM5P-AN

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

Also backport some patches improving QCA956x support.