Signed-off-by: David Bauer <mail@david-bauer.net>

Remove due to ticket #2939

These devices risk being bricked in a way that can not be recovered
without running full TFTP or serial recovery, as the flash ends up in a
read-only state with no way of upgrading to a fixed version.

Thus, remove the support for the time being. Don't just flag them as
BROKEN, as this would deliberately brick these boards when installating
such an image.

Signed-off-by: David Bauer <mail@david-bauer.net>

Signed-off-by: David Bauer <mail@david-bauer.net>

There is a new way to flash OpenWrt on the ASUS TUF AX4200 which does
not require to open the device.

Link: https://github.com/blocktrron/openwrt-asus-filogic-factory/releases/tag/filogic-v1



Signed-off-by: David Bauer <mail@david-bauer.net>

Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>

This target supports Arm SystemReady (EFI) compatible machines

Enterasys WS-AP3715i is a dualband wireless-N access point.
It comes in a similar casing as the WS-AP3825i, however the hardware is
fundamentally different from its bigger cousin.

Signed-off-by: David Bauer <mail@david-bauer.net>

Better known as ZyXEL Multy M1

Signed-off-by: David Bauer <mail@david-bauer.net>

Since the device isn't marked as broken it should be mentioned in the docs as a supported device.

These boards do not support DSA in OpenWrt and thus lack working
ethernet. Disable them for now.

Co-authored-by: Tom Herbers <mail@tomherbers.de>

This reverts commit 97efc8ab. (#2580)

Since the commit was openend the device was moved from ath79-generic to ath79-tiny ([4b5bd15](https://github.com/openwrt/openwrt/commit/4b5bd1509195bc8f19999ebe481b59356b5c3512)).

Therefore the commit breaks builds of the ath79-generic target (`unable to enable device 'ubnt_rocket-m'`).

It might be possible to add support for the ath79-tiny target, and with it the Rocket M2/M5 (XM), in the future.

Signed-off-by: Christoph Krapp <achterin@gmail.com>

I made the mistake of never looking at the rendered version
fixes 95e5d382
backport like 8b2cc206 is optional

This device is already supported.
It's a lantiq device that was entered as ar71xx
in to the list of supported device and therefore
removed before the release of Gluon 22.

Signed-off-by: David Bauer <mail@david-bauer.net>

The GL-MT1300 is a high-performance new generation pocket-sized router
that offers a powerful hardware and first-class cybersecurity protocol
with unique and modern design.

Specifications:
- SoC: MT7621A, Dual-Core @880MHz
- RAM: 256 MB DDR3
- Flash: 32 MB
- Ethernet: 3 x 10/100/1000: 2 x LAN + 1 x WAN
- Wireless: 1 x MT7615D Dual-Band 2.4GHz(400Mbps) + 5GHz(867Mbps)
- USB: 1 x USB 3.0 port
- Slot: 1 x MicroSD card slot
- Button: 1 x Reset button
- Switch: 1 x Mode switch
- LED: 1 x Blue LED + 1 x White LED

MAC addresses based on vendor firmware:
WAN : factory 0x4000
LAN : Mac from factory 0x4000 + 1
2.4GHz : factory 0x4
5GHz : Mac form factory 0x4 + 1

Flashing instructions:
1.Connect to one of LAN ports.
2.Set the static IP on the PC to 192.168.1.2.
3.Press the Reset button and power the device (do not release the button).
  After waiting for the blue led to flash 5 times, the white led will
  come on and release the button.
4.Browse the 192.168.1.1 web page and update firmware according to web
  tips.
5.The blue led will flash when the firmware is being upgraded.
6.The blue led stops blinking to indicate that the firmware upgrade is
  complete and U-Boot automatically starts the firmware.

add comments about lacking radios
Co-authored-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Co-authored-by: Matthias Schiffer <mschiffer@universe-factory.net>

The activated setup mode is indicated by the WLAN LED.

Co-authored-by: David Bauer <mail@david-bauer.net>

Direct migration from 19.07 is currently not possible.

Gone due to
commit 45c84a11 ("ar71xx: drop target")