Skip to content
Snippets Groups Projects
Select Git revision
  • ce324d11ecad46eefced6300bda82ea50470ad87
  • experimental default protected
  • v2023.2.5-ffs
  • nrb/ex400-remove-wps
  • nrb/airmax-test
  • v2023.2.4-ffs
  • nrb/ar9344-reset-sequence
  • autinerd/experimental-openwrt-24.10
  • v2023.2.3-ffs
  • v2023.2.2-ffs
  • v2023.2-ffs
  • v2023.1-ffs
  • v2022.1.4-ffs
  • feature/addMikrotikwAP
  • v2022.1.3-ffs
  • v2021.1.2-ffs
  • v2022.1.1-ffs
  • master protected
  • v2021.1.1-ffs
  • nrb/gluon-master-cpe510
  • v2021.1-ffs
  • experimental-2025-07-04
  • experimental-2025-07-04-base
  • experimental-2025-07-01
  • experimental-2025-07-01-base
  • experimental-2025-06-25
  • experimental-2025-06-25-base
  • experimental-2025-06-24
  • experimental-2025-06-24-base
  • experimental-2025-06-22
  • experimental-2025-06-22-base
  • v2023.2.5-ffs0.1
  • experimental-2025-06-08
  • experimental-2025-06-08-base
  • experimental-2025-06-06
  • experimental-2025-06-06-base
  • experimental-2025-05-27
  • experimental-2025-05-27-base
  • experimental-2025-05-18
  • experimental-2025-05-18-base
  • experimental-2025-05-15
41 results

ath79-generic

Blame
    • Sven Eckelmann's avatar
      ce324d11
      ath79-generic: add support for OpenMesh OM2P-HS v2 · ce324d11
      Sven Eckelmann authored
      Device specifications:
      ======================
      
      * Qualcomm/Atheros AR9341 rev 1
      * 535/400/200 MHz (CPU/DDR/AHB)
      * 64 MB of RAM
      * 16 MB of SPI NOR flash
        - 2x 7 MB available; but one of the 7 MB regions is the recovery image
      * 2x 10/100 Mbps Ethernet
      * 2T2R 2.4 GHz Wi-Fi
      * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
      * 1x GPIO-button (reset)
      * external h/w watchdog (enabled by default)
      * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
      * 2x fast ethernet
        - eth0
          + 802.3af POE
          + builtin switch port 1
          + used as LAN interface
        - eth1
          + 18-24V passive POE (mode B)
          + used as WAN interface
      * 12-24V 1A DC
      * internal antennas
      
      Flashing instructions:
      ======================
      
      Various methods can be used to install the actual image on the flash.
      Two easy ones are:
      
      ap51-flash
      ----------
      
      The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
      used to transfer the image to the u-boot when the device boots up.
      
      initramfs from TFTP
      -------------------
      
      The serial console must be used to access the u-boot shell during bootup.
      It can then be used to first boot up the initramfs image from a TFTP server
      (here with the IP 192.168.1.21):
      
          setenv serverip 192.168.1.21
          setenv ipaddr 192.168.1.1
          tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
      
      The actual sysupgrade image can then be transferred (on the LAN port) to
      the device via
      
          scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
      
      On the device, the sysupgrade must then be started using
      
          sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
      
      Gluon image name change
      =======================
      
      The device had the image name "openmesh-om2phsv2" in older versions of Gluon.
      This had to be changed with the new name in the device trees of the ath79
      device tree.
      ce324d11
      History
      ath79-generic: add support for OpenMesh OM2P-HS v2
      Sven Eckelmann authored
      Device specifications:
      ======================
      
      * Qualcomm/Atheros AR9341 rev 1
      * 535/400/200 MHz (CPU/DDR/AHB)
      * 64 MB of RAM
      * 16 MB of SPI NOR flash
        - 2x 7 MB available; but one of the 7 MB regions is the recovery image
      * 2x 10/100 Mbps Ethernet
      * 2T2R 2.4 GHz Wi-Fi
      * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
      * 1x GPIO-button (reset)
      * external h/w watchdog (enabled by default)
      * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
      * 2x fast ethernet
        - eth0
          + 802.3af POE
          + builtin switch port 1
          + used as LAN interface
        - eth1
          + 18-24V passive POE (mode B)
          + used as WAN interface
      * 12-24V 1A DC
      * internal antennas
      
      Flashing instructions:
      ======================
      
      Various methods can be used to install the actual image on the flash.
      Two easy ones are:
      
      ap51-flash
      ----------
      
      The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
      used to transfer the image to the u-boot when the device boots up.
      
      initramfs from TFTP
      -------------------
      
      The serial console must be used to access the u-boot shell during bootup.
      It can then be used to first boot up the initramfs image from a TFTP server
      (here with the IP 192.168.1.21):
      
          setenv serverip 192.168.1.21
          setenv ipaddr 192.168.1.1
          tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
      
      The actual sysupgrade image can then be transferred (on the LAN port) to
      the device via
      
          scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
      
      On the device, the sysupgrade must then be started using
      
          sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
      
      Gluon image name change
      =======================
      
      The device had the image name "openmesh-om2phsv2" in older versions of Gluon.
      This had to be changed with the new name in the device trees of the ath79
      device tree.
    mediatek-mt7622 283 B
    -- Linksys
    
    device('linksys-e8450-ubi', 'linksys_e8450-ubi', {
    	factory = false,
    	sysupgrade_ext = '.itb',
    })
    
    
    device('ubiquiti-unifi-6-lr', 'ubnt_unifi-6-lr', {
    	factory = false,
    })
    
    -- Xiaomi
    
    device('xiaomi-redmi-router-ax6s', 'xiaomi_redmi-router-ax6s', {
    	factory = false,
    })