Select Git revision
ath79-generic
-
Sven Eckelmann authoredDevice specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 3T3R 2.4 GHz Wi-Fi (11n) * 3T3R 5 GHz Wi-Fi (11ac) * 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 1x ethernet - AR8035 ethernet PHY (RGMII) - 10/100/1000 Mbps Ethernet - 802.3af POE - used as LAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Gluon image name change ======================= The device had the image name "openmesh-mr1750v2" in older versions of Gluon. This had to be changed with the new name in the device trees of the ath79 device tree.
Sven Eckelmann authoredDevice specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 3T3R 2.4 GHz Wi-Fi (11n) * 3T3R 5 GHz Wi-Fi (11ac) * 6x GPIO-LEDs (2x wifi, 2x status, 1x lan, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 1x ethernet - AR8035 ethernet PHY (RGMII) - 10/100/1000 Mbps Ethernet - 802.3af POE - used as LAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Gluon image name change ======================= The device had the image name "openmesh-mr1750v2" in older versions of Gluon. This had to be changed with the new name in the device trees of the ath79 device tree.
Makefile 15.78 KiB
all:
LC_ALL:=C
LANG:=C
export LC_ALL LANG
empty:=
space:= $(empty) $(empty)
GLUONMAKE_EARLY = $(SUBMAKE) -C $(GLUON_ORIGOPENWRTDIR) -f $(GLUONDIR)/Makefile GLUON_TOOLS=0 QUILT=
GLUONMAKE = $(SUBMAKE) -C $(GLUON_OPENWRTDIR) -f $(GLUONDIR)/Makefile
ifneq ($(OPENWRT_BUILD),1)
GLUONDIR:=${CURDIR}
include $(GLUONDIR)/include/gluon.mk
TOPDIR:=$(GLUON_ORIGOPENWRTDIR)
export TOPDIR
update: FORCE
$(GLUONDIR)/scripts/update.sh
$(GLUONDIR)/scripts/patch.sh
patch: FORCE
$(GLUONDIR)/scripts/patch.sh
unpatch: FORCE
$(GLUONDIR)/scripts/unpatch.sh
update-patches: FORCE
$(GLUONDIR)/scripts/update.sh
$(GLUONDIR)/scripts/update-patches.sh
$(GLUONDIR)/scripts/patch.sh
-include $(TOPDIR)/include/host.mk
_SINGLE=export MAKEFLAGS=$(space);
override OPENWRT_BUILD=1
override GLUON_TOOLS=1
GREP_OPTIONS=
export OPENWRT_BUILD GLUON_TOOLS GREP_OPTIONS
-include $(TOPDIR)/include/debug.mk
-include $(TOPDIR)/include/depends.mk
include $(GLUONDIR)/include/toplevel.mk
include $(GLUONDIR)/targets/targets.mk
CheckTarget := [ -n '$(GLUON_TARGET)' -a -n '$(GLUON_TARGET_$(GLUON_TARGET)_BOARD)' ] \
|| (echo -e 'Please set GLUON_TARGET to a valid target. Gluon supports the following targets:$(subst $(space),\n * ,$(GLUON_TARGETS))'; false)
CheckExternal := test -d $(GLUON_ORIGOPENWRTDIR) || (echo 'You don'"'"'t seem to have obtained the external repositories needed by Gluon; please call `make update` first!'; false)
create-key: FORCE
@$(CheckExternal)
+@$(GLUONMAKE_EARLY) create-key
prepare-target: FORCE
@$(CheckExternal)
@$(CheckTarget)
+@$(GLUONMAKE_EARLY) prepare-target