Skip to content
Snippets Groups Projects
Select Git revision
  • 979cc0a2edbd7f1465f3c25f0fc1b1365ecebd8a
  • experimental default protected
  • v2023.2.5-ffs
  • nrb/ex400-remove-wps
  • nrb/airmax-test
  • v2023.2.4-ffs
  • nrb/ar9344-reset-sequence
  • autinerd/experimental-openwrt-24.10
  • v2023.2.3-ffs
  • v2023.2.2-ffs
  • v2023.2-ffs
  • v2023.1-ffs
  • v2022.1.4-ffs
  • feature/addMikrotikwAP
  • v2022.1.3-ffs
  • v2021.1.2-ffs
  • v2022.1.1-ffs
  • master protected
  • v2021.1.1-ffs
  • nrb/gluon-master-cpe510
  • v2021.1-ffs
  • experimental-2025-07-01
  • experimental-2025-07-01-base
  • experimental-2025-06-25
  • experimental-2025-06-25-base
  • experimental-2025-06-24
  • experimental-2025-06-24-base
  • experimental-2025-06-22
  • experimental-2025-06-22-base
  • v2023.2.5-ffs0.1
  • experimental-2025-06-08
  • experimental-2025-06-08-base
  • experimental-2025-06-06
  • experimental-2025-06-06-base
  • experimental-2025-05-27
  • experimental-2025-05-27-base
  • experimental-2025-05-18
  • experimental-2025-05-18-base
  • experimental-2025-05-15
  • experimental-2025-05-15-base
  • experimental-2025-05-13
41 results

ath79-generic

Blame
    • Sven Eckelmann's avatar
      979cc0a2
      ath79-generic: Add support for OpenMesh OM5P-AN · 979cc0a2
      Sven Eckelmann authored
      Device specifications:
      ======================
      
      * Qualcomm/Atheros AR9344 rev 2
      * 560/450/225 MHz (CPU/DDR/AHB)
      * 64 MB of RAM
      * 16 MB of SPI NOR flash
        - 2x 7 MB available; but one of the 7 MB regions is the recovery image
      * 1T1R 2.4 GHz Wi-Fi
      * 2T2R 5 GHz Wi-Fi
      * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
      * 1x GPIO-button (reset)
      * external h/w watchdog (enabled by default)
      * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
      * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
      * 2x ethernet
        - eth0
          + AR8035 ethernet PHY
          + 10/100/1000 Mbps Ethernet
          + 802.3af POE
          + used as LAN interface
        - eth1
          + 10/100 Mbps Ethernet
          + builtin switch port 1
          + 18-24V passive POE (mode B)
          + used as WAN interface
      * 12-24V 1A DC
      * internal antennas
      
      Flashing instructions:
      ======================
      
      Various methods can be used to install the actual image on the flash.
      Two easy ones are:
      
      ap51-flash
      ----------
      
      The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
      used to transfer the image to the u-boot when the device boots up.
      
      initramfs from TFTP
      -------------------
      
      The serial console must be used to access the u-boot shell during bootup.
      It can then be used to first boot up the initramfs image from a TFTP server
      (here with the IP 192.168.1.21):
      
          setenv serverip 192.168.1.21
          setenv ipaddr 192.168.1.1
          tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
      
      The actual sysupgrade image can then be transferred (on the LAN port) to the
      device via
      
          scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
      
      On the device, the sysupgrade must then be started using
      
          sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
      979cc0a2
      History
      ath79-generic: Add support for OpenMesh OM5P-AN
      Sven Eckelmann authored
      Device specifications:
      ======================
      
      * Qualcomm/Atheros AR9344 rev 2
      * 560/450/225 MHz (CPU/DDR/AHB)
      * 64 MB of RAM
      * 16 MB of SPI NOR flash
        - 2x 7 MB available; but one of the 7 MB regions is the recovery image
      * 1T1R 2.4 GHz Wi-Fi
      * 2T2R 5 GHz Wi-Fi
      * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
      * 1x GPIO-button (reset)
      * external h/w watchdog (enabled by default)
      * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
      * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
      * 2x ethernet
        - eth0
          + AR8035 ethernet PHY
          + 10/100/1000 Mbps Ethernet
          + 802.3af POE
          + used as LAN interface
        - eth1
          + 10/100 Mbps Ethernet
          + builtin switch port 1
          + 18-24V passive POE (mode B)
          + used as WAN interface
      * 12-24V 1A DC
      * internal antennas
      
      Flashing instructions:
      ======================
      
      Various methods can be used to install the actual image on the flash.
      Two easy ones are:
      
      ap51-flash
      ----------
      
      The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
      used to transfer the image to the u-boot when the device boots up.
      
      initramfs from TFTP
      -------------------
      
      The serial console must be used to access the u-boot shell during bootup.
      It can then be used to first boot up the initramfs image from a TFTP server
      (here with the IP 192.168.1.21):
      
          setenv serverip 192.168.1.21
          setenv ipaddr 192.168.1.1
          tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
      
      The actual sysupgrade image can then be transferred (on the LAN port) to the
      device via
      
          scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
      
      On the device, the sysupgrade must then be started using
      
          sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
    modules 640 B
    GLUON_FEEDS='packages routing gluon'
    
    OPENWRT_REPO=https://github.com/openwrt/openwrt.git
    OPENWRT_BRANCH=openwrt-22.03
    OPENWRT_COMMIT=ca58b8b4feb7a56e262be7260032a06032264a48
    
    PACKAGES_PACKAGES_REPO=https://github.com/openwrt/packages.git
    PACKAGES_PACKAGES_BRANCH=openwrt-22.03
    PACKAGES_PACKAGES_COMMIT=5343d6a0935895de9abe960c8cc0d9aec094d0a9
    
    PACKAGES_ROUTING_REPO=https://github.com/openwrt/routing.git
    PACKAGES_ROUTING_BRANCH=openwrt-22.03
    PACKAGES_ROUTING_COMMIT=1ccc4e435175e6ba5ac60e626e1e95eb25c5757b
    
    PACKAGES_GLUON_REPO=https://github.com/freifunk-gluon/packages.git
    PACKAGES_GLUON_COMMIT=04d2b6ffbb6ee02012f2733b7752d8db0d12eaff