Select Git revision
ath79-generic
-
Sven Eckelmann authoredDevice specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Gluon image name change ======================= The device had the image name "openmesh-om5p-ac" in older versions of Gluon. This had to be changed with the new name in the device trees of the ath79 device tree.Sven Eckelmann authoredDevice specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Gluon image name change ======================= The device had the image name "openmesh-om5p-ac" in older versions of Gluon. This had to be changed with the new name in the device trees of the ath79 device tree.
ath79-generic 5.65 KiB
local ATH10K_PACKAGES_QCA9880 = {
'kmod-ath10k',
'-kmod-ath10k-ct',
'-kmod-ath10k-ct-smallbuffers',
'ath10k-firmware-qca988x',
'-ath10k-firmware-qca988x-ct',
}
local ATH10K_PACKAGES_QCA9887 = {
'kmod-ath10k',
'-kmod-ath10k-ct',
'-kmod-ath10k-ct-smallbuffers',
'ath10k-firmware-qca9887',
'-ath10k-firmware-qca9887-ct',
}
local ATH10K_PACKAGES_QCA9888 = {
'kmod-ath10k',
'-kmod-ath10k-ct',
'-kmod-ath10k-ct-smallbuffers',
'ath10k-firmware-qca9888',
'-ath10k-firmware-qca9888-ct',
}
-- devolo
device('devolo-wifi-pro-1200e', 'devolo_dvl1200e', {
packages = ATH10K_PACKAGES_QCA9880,
factory = false,
})
device('devolo-wifi-pro-1200i', 'devolo_dvl1200i', {
packages = ATH10K_PACKAGES_QCA9880,
factory = false,
})
device('devolo-wifi-pro-1750c', 'devolo_dvl1750c', {
packages = ATH10K_PACKAGES_QCA9880,
factory = false,
})
device('devolo-wifi-pro-1750e', 'devolo_dvl1750e', {
packages = ATH10K_PACKAGES_QCA9880,
factory = false,
})
device('devolo-wifi-pro-1750i', 'devolo_dvl1750i', {
packages = ATH10K_PACKAGES_QCA9880,
factory = false,
})
device('devolo-wifi-pro-1750x', 'devolo_dvl1750x', {
packages = ATH10K_PACKAGES_QCA9880,
factory = false,
})
-- Enterasys
device('enterasys-ws-ap3705', 'enterasys_ws-ap3705i', {
factory = false,
})
-- GL.iNet
device('gl.inet-gl-ar300m-lite', 'glinet_gl-ar300m-lite', {
factory = false,
})