Skip to content
Snippets Groups Projects
  • Björn Dobe's avatar
    a492e629
    ipq40xx: add support for Aruba AP-303H / Instant ON AP11D (#2302) · a492e629
    Björn Dobe authored
    - [x] must be flashable from vendor firmware
      - [ ] webinterface
      - [ ] tftp
      - [x] other: Console port available. Manufacturer specific cable required.
            Tutorial in OpenWRT commit message https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=c6e972c8772a628a1a2f2e5590d7c6f4acef9ab0
    - [x] must support upgrade mechanism
      - [x] must have working sysupgrade
        - [x] must keep/forget configuration (if applicable)
          *think `sysupgrade [-n]` or `firstboot`*
      - [x] must have working autoupdate
            root@Aruba-AP-303H:~# lua -e 'print(require("platform_info").get_image_name())'
            aruba-ap-303h
    - [x] reset/wps/phone button must return device into config mode
    - [x] primary mac should match address on device label (or packaging) (https://gluon.readthedocs.io/en/latest/dev/hardware.html#notes)
    - wired network
      - [x] should support all network ports on the device
      - [x] must have correct port assignment (WAN/LAN)
    - wifi (if applicable)
      - [x] association with AP must be possible on all radios
      - [x] association with 802.11s mesh must be working on all radios
      - [x] ap/mesh mode must work in parallel on all radios
    - led mapping
      - power/sys led (_critical, because led definitions are setup on firstboot only_)
        - [x] lit while the device is on
        - [x] should display config mode blink sequence
    (https://gluon.readthedocs.io/en/latest/features/configmode.html)
      - radio leds
        - [x] should map to their respective radio
        - [x] should show activity
      - switchport leds
        - [x] should map to their respective port (or switch, if only one led present)
        - [x] should show link state and activity
    - outdoor devices only
      - [ ] added board name to `is_outdoor_device` function in `package/gluon-core/luasrc/usr/lib/lua/gluon/platform.lua`
    - ToDo (upstream):
      - enable PoE pass through on interface E3
            system.poe_passthrough=gpio_switch
            system.poe_passthrough.name='PoE Passthrough'
            system.poe_passthrough.gpio_pin='446'
            system.poe_passthrough.value='0' (0 is active)
    ipq40xx: add support for Aruba AP-303H / Instant ON AP11D (#2302)
    Björn Dobe authored
    - [x] must be flashable from vendor firmware
      - [ ] webinterface
      - [ ] tftp
      - [x] other: Console port available. Manufacturer specific cable required.
            Tutorial in OpenWRT commit message https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=c6e972c8772a628a1a2f2e5590d7c6f4acef9ab0
    - [x] must support upgrade mechanism
      - [x] must have working sysupgrade
        - [x] must keep/forget configuration (if applicable)
          *think `sysupgrade [-n]` or `firstboot`*
      - [x] must have working autoupdate
            root@Aruba-AP-303H:~# lua -e 'print(require("platform_info").get_image_name())'
            aruba-ap-303h
    - [x] reset/wps/phone button must return device into config mode
    - [x] primary mac should match address on device label (or packaging) (https://gluon.readthedocs.io/en/latest/dev/hardware.html#notes)
    - wired network
      - [x] should support all network ports on the device
      - [x] must have correct port assignment (WAN/LAN)
    - wifi (if applicable)
      - [x] association with AP must be possible on all radios
      - [x] association with 802.11s mesh must be working on all radios
      - [x] ap/mesh mode must work in parallel on all radios
    - led mapping
      - power/sys led (_critical, because led definitions are setup on firstboot only_)
        - [x] lit while the device is on
        - [x] should display config mode blink sequence
    (https://gluon.readthedocs.io/en/latest/features/configmode.html)
      - radio leds
        - [x] should map to their respective radio
        - [x] should show activity
      - switchport leds
        - [x] should map to their respective port (or switch, if only one led present)
        - [x] should show link state and activity
    - outdoor devices only
      - [ ] added board name to `is_outdoor_device` function in `package/gluon-core/luasrc/usr/lib/lua/gluon/platform.lua`
    - ToDo (upstream):
      - enable PoE pass through on interface E3
            system.poe_passthrough=gpio_switch
            system.poe_passthrough.name='PoE Passthrough'
            system.poe_passthrough.gpio_pin='446'
            system.poe_passthrough.value='0' (0 is active)