Skip to content
Snippets Groups Projects
Select Git revision
  • experimental default protected
  • nrb/airmax-test
  • v2023.2.4-ffs
  • nrb/ar9344-reset-sequence
  • autinerd/experimental-openwrt-24.10
  • v2023.2.3-ffs
  • v2023.2.2-ffs
  • v2023.2-ffs
  • v2023.1-ffs
  • v2022.1.4-ffs
  • feature/addMikrotikwAP
  • v2022.1.3-ffs
  • v2021.1.2-ffs
  • v2022.1.1-ffs
  • master protected
  • v2021.1.1-ffs
  • nrb/gluon-master-cpe510
  • v2021.1-ffs
  • v2020.2.3-ffs
  • nrbffs/fastd-remove-delay
  • experimental-2025-05-27
  • experimental-2025-05-27-base
  • experimental-2025-05-18
  • experimental-2025-05-18-base
  • experimental-2025-05-15
  • experimental-2025-05-15-base
  • experimental-2025-05-13
  • experimental-2025-05-13-base
  • experimental-2025-05-08
  • experimental-2025-05-08-base
  • experimental-2025-05-05
  • experimental-2025-05-05-base
  • experimental-2025-05-02
  • experimental-2025-05-02-base
  • experimental-2025-05-01
  • experimental-2025-05-01-base
  • experimental-2025-04-29
  • experimental-2025-04-29-base
  • experimental-2025-04-27
  • experimental-2025-04-27-base
40 results

ar71xx-generic

Blame
    • David Bauer's avatar
      22d45448
      ar71xx: add support for Fritz!Box 4020 · 22d45448
      David Bauer authored
      
      This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
      
      SoC:   Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
      RAM:   Winbond W971GG6KB-25
      FLASH: Macronix MX25L12835F
      WiFi:  QCA9561 b/g/n 3x3 450Mbit/s
      USB:   1x USB 2.0
      IN:    WPS button, WiFi button
      OUT:   Power LED green, Internet LED green, WLAN LED green,
             LAN LED green, INFO LED green, INFO LED red
      UART:  Header Next to Black metal shield
             Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
             The Serial setting is 115200-8-N-1.
      
      Tested and working:
       - Ethernet (LAN + WAN)
       - WiFi (correct MAC)
       - Installation via EVA bootloader
       - OpenWRT sysupgrade
       - Buttons
       - LEDs
      
      Not working:
       - USB port
      
      Installation via EVA:
      In the first seconds after Power is connected, the bootloader will
      listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
      like following:
      
        ftp> quote USER adam2
        ftp> quote PASS adam2
        ftp> binary
        ftp> debug
        ftp> passive
        ftp> quote MEDIA FLSH
        ftp> put openwrt-sysupgrade.bin mtd1
      
      Note that this procedure might take up to two minutes. After transfer is
      complete you need to powercycle the device to boot OpenWRT.
      
      Signed-off-by: default avatarDavid Bauer <mail@david-bauer.net>
      22d45448
      History
      ar71xx: add support for Fritz!Box 4020
      David Bauer authored
      
      This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
      
      SoC:   Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
      RAM:   Winbond W971GG6KB-25
      FLASH: Macronix MX25L12835F
      WiFi:  QCA9561 b/g/n 3x3 450Mbit/s
      USB:   1x USB 2.0
      IN:    WPS button, WiFi button
      OUT:   Power LED green, Internet LED green, WLAN LED green,
             LAN LED green, INFO LED green, INFO LED red
      UART:  Header Next to Black metal shield
             Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
             The Serial setting is 115200-8-N-1.
      
      Tested and working:
       - Ethernet (LAN + WAN)
       - WiFi (correct MAC)
       - Installation via EVA bootloader
       - OpenWRT sysupgrade
       - Buttons
       - LEDs
      
      Not working:
       - USB port
      
      Installation via EVA:
      In the first seconds after Power is connected, the bootloader will
      listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
      like following:
      
        ftp> quote USER adam2
        ftp> quote PASS adam2
        ftp> binary
        ftp> debug
        ftp> passive
        ftp> quote MEDIA FLSH
        ftp> put openwrt-sysupgrade.bin mtd1
      
      Note that this procedure might take up to two minutes. After transfer is
      complete you need to powercycle the device to boot OpenWRT.
      
      Signed-off-by: default avatarDavid Bauer <mail@david-bauer.net>