Skip to content
Snippets Groups Projects
Select Git revision
  • 22d45448fddb7b05ddddb747ff72cebd2f1dc1a2
  • experimental
  • master
  • v2021.1.2-ffs
  • v2021.1.1-ffs
  • nrb/gluon-master-cpe510
  • v2021.1-ffs
  • v2020.2.3-ffs
  • nrbffs/fastd-remove-delay
  • v2020.2.2-ffs
  • v2020.2.1-ffs
  • v2020.2-ffs
  • v2020.2.x
  • v2020.1.3-ffs
  • v2020.1.1-ffs
  • v2020.1-ffs
  • v2019.1.2-ffs
  • v2019.1.1-ffs
  • nrb/test-radv-filter
  • v2019.1-ffs
  • nrbffs/netgear-ex6120
  • v2021.1.2-ffs0.2
  • v2021.1.2-ffs0.1
  • v2021.1.1-ffs0.4
  • v2021.1.1-ffs0.3
  • v2021.1.1-ffs0.2
  • v2021.1.1-ffs0.1
  • v2021.1-ffs0.1
  • v2020.2.3-ffs0.3
  • v2020.2.3-ffs0.2
  • v2020.2.3-ffs0.1
  • v2020.2.2-ffs0.1
  • v2020.2.1-ffs0.1
  • v2020.2-ffs0.1
  • v2020.2
  • v2020.2.x-ffs0.1
  • v2020.1.3-ffs0.1
  • v2020.1.1-ffs0.1
  • v2020.1-ffs0.1
  • v2019.1.2-ffs0.1
  • v2019.1.1-ffs0.1
41 results

0084-ar71xx-add-support-for-Fritz-Box-4020.patch

Blame
  • Forked from firmware / FFS Gluon
    Source project has a limited visibility.
    • David Bauer's avatar
      22d45448
      ar71xx: add support for Fritz!Box 4020 · 22d45448
      David Bauer authored
      
      This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
      
      SoC:   Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
      RAM:   Winbond W971GG6KB-25
      FLASH: Macronix MX25L12835F
      WiFi:  QCA9561 b/g/n 3x3 450Mbit/s
      USB:   1x USB 2.0
      IN:    WPS button, WiFi button
      OUT:   Power LED green, Internet LED green, WLAN LED green,
             LAN LED green, INFO LED green, INFO LED red
      UART:  Header Next to Black metal shield
             Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
             The Serial setting is 115200-8-N-1.
      
      Tested and working:
       - Ethernet (LAN + WAN)
       - WiFi (correct MAC)
       - Installation via EVA bootloader
       - OpenWRT sysupgrade
       - Buttons
       - LEDs
      
      Not working:
       - USB port
      
      Installation via EVA:
      In the first seconds after Power is connected, the bootloader will
      listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
      like following:
      
        ftp> quote USER adam2
        ftp> quote PASS adam2
        ftp> binary
        ftp> debug
        ftp> passive
        ftp> quote MEDIA FLSH
        ftp> put openwrt-sysupgrade.bin mtd1
      
      Note that this procedure might take up to two minutes. After transfer is
      complete you need to powercycle the device to boot OpenWRT.
      
      Signed-off-by: default avatarDavid Bauer <mail@david-bauer.net>
      22d45448
      History
      ar71xx: add support for Fritz!Box 4020
      David Bauer authored
      
      This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
      
      SoC:   Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
      RAM:   Winbond W971GG6KB-25
      FLASH: Macronix MX25L12835F
      WiFi:  QCA9561 b/g/n 3x3 450Mbit/s
      USB:   1x USB 2.0
      IN:    WPS button, WiFi button
      OUT:   Power LED green, Internet LED green, WLAN LED green,
             LAN LED green, INFO LED green, INFO LED red
      UART:  Header Next to Black metal shield
             Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
             The Serial setting is 115200-8-N-1.
      
      Tested and working:
       - Ethernet (LAN + WAN)
       - WiFi (correct MAC)
       - Installation via EVA bootloader
       - OpenWRT sysupgrade
       - Buttons
       - LEDs
      
      Not working:
       - USB port
      
      Installation via EVA:
      In the first seconds after Power is connected, the bootloader will
      listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
      like following:
      
        ftp> quote USER adam2
        ftp> quote PASS adam2
        ftp> binary
        ftp> debug
        ftp> passive
        ftp> quote MEDIA FLSH
        ftp> put openwrt-sysupgrade.bin mtd1
      
      Note that this procedure might take up to two minutes. After transfer is
      complete you need to powercycle the device to boot OpenWRT.
      
      Signed-off-by: default avatarDavid Bauer <mail@david-bauer.net>
    Makefile 585 B
    include $(TOPDIR)/rules.mk
    
    PKG_NAME:=gluon-config-mode-geo-location-osm
    PKG_VERSION:=1
    
    include ../gluon.mk
    
    define Package/gluon-config-mode-geo-location-osm
      TITLE:=Set geographic location of a node (map support)
      DEPENDS:=+gluon-config-mode-geo-location +gluon-web-osm
    endef
    
    define Package/gluon-config-mode-geo-location-osm/install
    	$(Gluon/Build/Install)
    
    	$(INSTALL_DIR) $(1)/lib/gluon/config-mode/www/static/
    	$(LN) /lib/gluon/web/www/static/gluon-web-osm.js $(1)/lib/gluon/config-mode/www/static/
    endef
    
    $(eval $(call BuildPackageGluon,gluon-config-mode-geo-location-osm))