Select Git revision
ipq40xx-generic
-
Björn Dobe authored- [x] must be flashable from vendor firmware - [ ] webinterface - [ ] tftp - [x] other: Console port available. Manufacturer specific cable required. Tutorial in OpenWRT commit message https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=c6e972c8772a628a1a2f2e5590d7c6f4acef9ab0 - [x] must support upgrade mechanism - [x] must have working sysupgrade - [x] must keep/forget configuration (if applicable) *think `sysupgrade [-n]` or `firstboot`* - [x] must have working autoupdate root@Aruba-AP-303H:~# lua -e 'print(require("platform_info").get_image_name())' aruba-ap-303h - [x] reset/wps/phone button must return device into config mode - [x] primary mac should match address on device label (or packaging) (https://gluon.readthedocs.io/en/latest/dev/hardware.html#notes) - wired network - [x] should support all network ports on the device - [x] must have correct port assignment (WAN/LAN) - wifi (if applicable) - [x] association with AP must be possible on all radios - [x] association with 802.11s mesh must be working on all radios - [x] ap/mesh mode must work in parallel on all radios - led mapping - power/sys led (_critical, because led definitions are setup on firstboot only_) - [x] lit while the device is on - [x] should display config mode blink sequence (https://gluon.readthedocs.io/en/latest/features/configmode.html) - radio leds - [x] should map to their respective radio - [x] should show activity - switchport leds - [x] should map to their respective port (or switch, if only one led present) - [x] should show link state and activity - outdoor devices only - [ ] added board name to `is_outdoor_device` function in `package/gluon-core/luasrc/usr/lib/lua/gluon/platform.lua` - ToDo (upstream): - enable PoE pass through on interface E3 system.poe_passthrough=gpio_switch system.poe_passthrough.name='PoE Passthrough' system.poe_passthrough.gpio_pin='446' system.poe_passthrough.value='0' (0 is active)Björn Dobe authored- [x] must be flashable from vendor firmware - [ ] webinterface - [ ] tftp - [x] other: Console port available. Manufacturer specific cable required. Tutorial in OpenWRT commit message https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=c6e972c8772a628a1a2f2e5590d7c6f4acef9ab0 - [x] must support upgrade mechanism - [x] must have working sysupgrade - [x] must keep/forget configuration (if applicable) *think `sysupgrade [-n]` or `firstboot`* - [x] must have working autoupdate root@Aruba-AP-303H:~# lua -e 'print(require("platform_info").get_image_name())' aruba-ap-303h - [x] reset/wps/phone button must return device into config mode - [x] primary mac should match address on device label (or packaging) (https://gluon.readthedocs.io/en/latest/dev/hardware.html#notes) - wired network - [x] should support all network ports on the device - [x] must have correct port assignment (WAN/LAN) - wifi (if applicable) - [x] association with AP must be possible on all radios - [x] association with 802.11s mesh must be working on all radios - [x] ap/mesh mode must work in parallel on all radios - led mapping - power/sys led (_critical, because led definitions are setup on firstboot only_) - [x] lit while the device is on - [x] should display config mode blink sequence (https://gluon.readthedocs.io/en/latest/features/configmode.html) - radio leds - [x] should map to their respective radio - [x] should show activity - switchport leds - [x] should map to their respective port (or switch, if only one led present) - [x] should show link state and activity - outdoor devices only - [ ] added board name to `is_outdoor_device` function in `package/gluon-core/luasrc/usr/lib/lua/gluon/platform.lua` - ToDo (upstream): - enable PoE pass through on interface E3 system.poe_passthrough=gpio_switch system.poe_passthrough.name='PoE Passthrough' system.poe_passthrough.gpio_pin='446' system.poe_passthrough.value='0' (0 is active)